SANIT DCE is a range of hot water tanks with capacities from 100 - 250 litres, manufactured in stainless steel, for supplying domestic hot water.
They include a double-wall "water bath” type heat exchanger and can be used with any type of heating power (thermal solar, gas, gas-oil, electricity, biomass, heat pump, etc).
Dual-chamber tanks for production and storage of domestic hot water, with capacities ranging from 100 litres to 250 litres.
Coupled with a heating boiler, DOMUSA TEKNIK is able to provide the right level of comfort for your home and provide a balanced and economical domestic hot water supply when accompanied by accompanied by a suitable hydraulic installation.
The careful design of the tank and casing allows the tank to give exceptional performance, enabling its use with a boiler, solar panel, or heat pump.
The SANIT tanks are built of stainless steel, complying with the strictest hygiene requirements. This material also has a high transmission coefficient that gives the tank a great capacity to produce domestic hot water.
Stainless steel is a material with exceptional properties in terms of peeling, oxidation, and sedimentation.
On its surface, a patina is created naturally, causing a self-protection that prevents oxidation even in installations with extremely corrosive waters.
Thermally insulated with rigid moulded polyurethane foam, all models have an access opening at the top, which facilitates cleaning of the tank. It also includes an outlet intended for electrical resistance.
Sanit DCE:
Tank for free-standing or wall installation with a dual-casing exchange system equipped with a control and regulation system for combination with any kind of boiler.
MODELS | SANIT DCE 100 | SANIT DCE 150 | SANIT DCE 200 | SANIT DCE 250 | |
---|---|---|---|---|---|
Base dimensions | mm | Ø581 | Ø581 | Ø581 | Ø608 |
Height dimensions | mm | 898 | 1,227 | 1,563 | 1,628 |
TP1 Drain valve inlet | Ø | 1/2” H | 1/2” H | 1/2” H | 1/2” H |
TP2 Drain valve inlet | Ø | 3/8” H | 3/8” H | 3/8” H | 3/8” H |
Cold water input | Ø | 3/4” M | 3/4” M | 3/4” M | 3/4” M |
Hot water output | Ø | 3/4” M | 3/4” M | 3/4” M | 3/4” M |
Primary inlet/outlet | Ø | 1” H | 1” H | 1” H | 1” H |
PI height – dimension A | mm | 620 | 900 | 1,200 | 1,491 |
MODELS | SANIT DCE 100 | SANIT DCE 150 | SANIT DCE 200 | SANIT DCE 250 | |
---|---|---|---|---|---|
Characteristics | |||||
Installation | floor / wall / horizontal | floor / wall / horizontal | floor / wall / horizontal | floor / wall / horizontal | |
Total volume | L. | 100 | 150 | 200 | 250 |
Max. storage temperature | ºC | 90 | 90 | 90 | 90 |
Maximum working pressure of the tank | bar | 7 | 7 | 7 | 7 |
Max. primary temperature | ºC | 110 | 110 | 110 | 110 |
Maximum primary working pressure | bar | 3 | 3 | 3 | 3 |
Operation | |||||
Continuous flow l/h D 30º | Qp 1 m3/h Qp 3 m3/h Qp 5 m3/h |
602 745 831 |
766 825 944 |
844 942 1,046 |
930 1,038 1,143 |
Peak flow l/10 min D 30º | Qp 1 m3/h Qp 3 m3/h Qp 5 m3/h |
266 290 305 |
378 388 407 |
474 490 507 |
571 589 607 |
Flow up to 1 hour l/h D 30º | Qp 1 m3/h Qp 3 m3/h Qp 5 m3/h |
702 845 931 |
916 975 1,094 |
1,044 1,142 1,246 |
1,180 1,288 1,393 |
Power transmitted kW | Qp 1 m3/h Qp 3 m3/h Qp 5 m3/h |
21 26 29 |
27 29 33 |
29 33 36 |
30 36 40 |
DHW efficiency class |
Qp: Primary flow rate / Primary temperature 80°C / Storage temperature 60°C
MODELS | SANIT DCE |
---|---|
Thermometer | |
Adjustable thermostat | |
On/off switch |
S 200 hydraulic kit: |
Dielectric sleeves |
Safety unit |
8 L expansion vessel |
Cathodic protection |
1.5 kW/2.5 kW/3.5 kW electrical resistor |
Board bracket |
Elliptic cover with resistor inlet |
100 L / 1.5 kW resistor kit |
100 L / 2.5 kW resistor kit |
150 L / 1.5 kW resistor kit |
150 L / 2.5 kW resistor kit |
200-250 L / 1.5 kW resistor kit |
200-250 L / 2.5 kW resistor kit |